Tutorial for Tilted Square Framing

The tilted/tipsy square frame is a useful way to enlarge a block. Here is the sample I will use for measurement examples:

Unnamed block

Finished center 7 1/2 x 7 1/2; Unfinished block 12 1/2 x 12 1/2

Measure your center (and remember you will lose 1/2 inch to seams. Mine measured 8 inches, so it will become 7 1/2 inches finished.

You will be cutting two rectangles then cutting on the diagonal to get four triangles.

To get the width needed for the triangle, subtract the finished measurement of the center from the desired finished measurement of the block to get the needed width to add (12 – 7 1/2 = 4 1/2 inches in the example) .  (The principle here is to design from finished measurements then add seam allowance when planning the cutting.)   To plan the rectangle to cut, add an inch and a half to the finished width for seam allowance to be on the safe side, and cut a strip (6 inch strip for the example). The extra is for the loss when seaming sharp angles. There will be some trimming at the end. The very daring quilters can experiment with smaller seam allowances if you are willing to trim smaller than your desired  size if necessary. Remember that 7/8 inch is the exact amount to add to HSTs, so no less than that.

Now for the length of the rectangles. Add an inch and a half to your desired  finished block size. (For the example, the end result desired is 12 inches so I cut 13 1/2).

Cut two rectangles, then cut the diagonal to get four triangles.  About that diagonal. If you want to be able to put the pieced center on top when you sew, cut the diagonal from upper left to lower right. (If using a solid, it doesn’t matter because there is no right and wrong side to most solids. If you don’t care which piece is on top it doesn’t matter; if you cut the opposite way, start sewing on the other side.)

diagonal cut

Lining up for the first partial seam.

Lining up the pieces

Note that the STRAIGHT edge lines up with the left side of the center and the top is a straight line. Flip the center piece onto the triangle so that right sides are together and start sewing at the top corner, ending about 2 inches from the bottom of the center piece.

First seam

You will fix that hanging bit of the triangle after the third seam.  Press the seam however you like.

Now you are ready to make a complete seam with the next triangles.

second and third seam placeent

Note how you always attach the straight edge to the corner away from the previous triangle, and now it is possible to sew the whole length of the seams. Press after each seam.

For the fourth triangle, fold up the tail of the first triangle to where you stopped sewing.

fourth seam position

Now there is room for a complete seam. Sew then press. Then simply fold down the first triangle and finish that seam and press.

Use a square ruler to trim the block to the UNFINISHED size (in the case of the example, 12 1/2 x 12 1/2). Position the ruler so that the four points of the center  square are as close to an equal distance from the 12 1/2 edge as possible. (Mine are usually 1/8-1/4 off.  But it is a tipsy square, so a little variance doesn’t really matter. You will be trimming all four sides. (The photo of the example looks like the right is off by more; I don’t remember if that is a fact of the photo or the block itself, and the blockis already gone, so I can’t check.)

Don’t you love the high tech illustrations? 🙂

Linking with “Tips and Tutorials Tuesdays”–link in sidebar.

Advertisements

8 Comments

Filed under quilting, tutorial

8 responses to “Tutorial for Tilted Square Framing

  1. Thank you for your detailed tutorial Claire.It reminds me on my Dancing Boxes block …. (https://knettycraft.wordpress.com/2015/05/21/dancing-boxes-finished/ ) But that was made in a totally different way.

  2. This tutorial is just what I was looking for to get moving on a baby quilt from scraps that I had been planning. Thank you so much.

  3. Cher

    Great tutorial !! another fun way to use up scraps/orphan blocks or just create a great quilt from planned blocks using this approach.

  4. dezertsuz

    Yep, newspaper is high tech for me. =) I didn’t notice one side being bigger, but I can check if you like. Thanks for the tutorial.

  5. I like your method a lot Claire, because you don’t waste fabric this way. I’ll be doing some of this type of framing soon, so your lesson comes in very handy. Thanks!

  6. Paula

    WOW! this tutorial is exactly what I’ve been looking for. I’ve never tried the tilted block yet, cos I really hate to waste fabric. Thank you so much for putting your proficiency out there for all of us!

Conversation is good, so please join in. I'll reply here if it seems relevant to others, by email, or by visiting your blog.

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s